| AUTORESUME_EN_R | Field AUTORESUME_EN reader - Enable the auto resume feature, when set, HW will use 32KHz clock to send Resume to respond to the device remote wakeup(for host mode only)
|
| AUTORESUME_EN_W | Field AUTORESUME_EN writer - Enable the auto resume feature, when set, HW will use 32KHz clock to send Resume to respond to the device remote wakeup(for host mode only)
|
| CLKGATE_R | Field CLKGATE reader - Gate UTMI Clocks
|
| CLKGATE_W | Field CLKGATE writer - Gate UTMI Clocks
|
| CTRL_SET_SPEC | USB PHY General Control Register
|
| DEVPLUGIN_IRQ_R | Field DEVPLUGIN_IRQ reader - Indicates that the device is connected
|
| DEVPLUGIN_IRQ_W | Field DEVPLUGIN_IRQ writer - Indicates that the device is connected
|
| DEVPLUGIN_POLARITY_R | Field DEVPLUGIN_POLARITY reader - Device plugin polarity: For device mode, if this bit is cleared to 0, then it trips the interrupt if the device is plugged in
|
| DEVPLUGIN_POLARITY_W | Field DEVPLUGIN_POLARITY writer - Device plugin polarity: For device mode, if this bit is cleared to 0, then it trips the interrupt if the device is plugged in
|
| ENAUTOCLR_CLKGATE_R | Field ENAUTOCLR_CLKGATE reader - Enables the feature to auto-clear the CLKGATE bit if there is wakeup event while USB is suspended
|
| ENAUTOCLR_CLKGATE_W | Field ENAUTOCLR_CLKGATE writer - Enables the feature to auto-clear the CLKGATE bit if there is wakeup event while USB is suspended
|
| ENAUTOCLR_PHY_PWD_R | Field ENAUTOCLR_PHY_PWD reader - Enables the feature to auto-clear the PWD register bits in PWD if there is wakeup event while USB is suspended
|
| ENAUTOCLR_PHY_PWD_W | Field ENAUTOCLR_PHY_PWD writer - Enables the feature to auto-clear the PWD register bits in PWD if there is wakeup event while USB is suspended
|
| ENAUTOCLR_USBCLKGATE_R | Field ENAUTOCLR_USBCLKGATE reader - Enable auto-clear USB Clock gate: Enables the feature to auto-clear the USB0_CLKGATE/USB1_CLKGATE register bit in HW_DIGCTL_CTRL if there is wake-up event on USB0/USB1 while USB0/USB1 is suspended
|
| ENAUTOCLR_USBCLKGATE_W | Field ENAUTOCLR_USBCLKGATE writer - Enable auto-clear USB Clock gate: Enables the feature to auto-clear the USB0_CLKGATE/USB1_CLKGATE register bit in HW_DIGCTL_CTRL if there is wake-up event on USB0/USB1 while USB0/USB1 is suspended
|
| ENAUTOSET_USBCLKS_R | Field ENAUTOSET_USBCLKS reader - Enable auto-set of USB clocks: Enables the feature to auto-clear the EN_USB_CLKS register bits in HW_CLKCTRL_PLL1CTRL0/HW_CLKCTRL_P LL1CTRL1 if there is wake-up event on USB0/USB1 while USB0/USB1 is suspended
|
| ENAUTOSET_USBCLKS_W | Field ENAUTOSET_USBCLKS writer - Enable auto-set of USB clocks: Enables the feature to auto-clear the EN_USB_CLKS register bits in HW_CLKCTRL_PLL1CTRL0/HW_CLKCTRL_P LL1CTRL1 if there is wake-up event on USB0/USB1 while USB0/USB1 is suspended
|
| ENDEVPLUGINDET_R | Field ENDEVPLUGINDET reader - Enables non-standard resistive plugged-in detection This bit field controls connection of nominal 200kohm resistors to both the USB_DP and USB_DM pins as one method of detecting when a USB cable is attached in device mode
|
| ENDEVPLUGINDET_W | Field ENDEVPLUGINDET writer - Enables non-standard resistive plugged-in detection This bit field controls connection of nominal 200kohm resistors to both the USB_DP and USB_DM pins as one method of detecting when a USB cable is attached in device mode
|
| ENDPDMCHG_WKUP_R | Field ENDPDMCHG_WKUP reader - Enable DP DM change wake-up: Not for customer use
|
| ENDPDMCHG_WKUP_W | Field ENDPDMCHG_WKUP writer - Enable DP DM change wake-up: Not for customer use
|
| ENHOSTDISCONDETECT_R | Field ENHOSTDISCONDETECT reader - For host mode, enables high-speed disconnect detector
|
| ENHOSTDISCONDETECT_W | Field ENHOSTDISCONDETECT writer - For host mode, enables high-speed disconnect detector
|
| ENIRQHOSTDISCON_R | Field ENIRQHOSTDISCON reader - Enable IRQ for Host disconnect: Enables interrupt for detection of disconnection to Device when in high-speed host mode
|
| ENIRQHOSTDISCON_W | Field ENIRQHOSTDISCON writer - Enable IRQ for Host disconnect: Enables interrupt for detection of disconnection to Device when in high-speed host mode
|
| ENIRQRESUMEDETECT_R | Field ENIRQRESUMEDETECT reader - Enable IRQ Resume detect: Enables interrupt for detection of a non-J state on the USB line
|
| ENIRQRESUMEDETECT_W | Field ENIRQRESUMEDETECT writer - Enable IRQ Resume detect: Enables interrupt for detection of a non-J state on the USB line
|
| ENIRQWAKEUP_R | Field ENIRQWAKEUP reader - Enable wake-up IRQ: Enables interrupt for the wake-up events.
|
| ENIRQWAKEUP_W | Field ENIRQWAKEUP writer - Enable wake-up IRQ: Enables interrupt for the wake-up events.
|
| ENUTMILEVEL2_R | Field ENUTMILEVEL2 reader - Enables UTMI+ Level 2 operation for the USB HS PHY
|
| ENUTMILEVEL2_W | Field ENUTMILEVEL2 writer - Enables UTMI+ Level 2 operation for the USB HS PHY
|
| ENUTMILEVEL3_R | Field ENUTMILEVEL3 reader - Enables UTMI+ Level 3 operation for the USB HS PHY
|
| ENUTMILEVEL3_W | Field ENUTMILEVEL3 writer - Enables UTMI+ Level 3 operation for the USB HS PHY
|
| ENVBUSCHG_WKUP_R | Field ENVBUSCHG_WKUP reader - Enable VBUS change wake-up: Enables the feature to wake-up USB if VBUS is toggled when USB is suspended
|
| ENVBUSCHG_WKUP_W | Field ENVBUSCHG_WKUP writer - Enable VBUS change wake-up: Enables the feature to wake-up USB if VBUS is toggled when USB is suspended
|
| HOSTDISCONDETECT_IRQ_R | Field HOSTDISCONDETECT_IRQ reader - Indicates that the device has disconnected in High-Speed mode
|
| HOSTDISCONDETECT_IRQ_W | Field HOSTDISCONDETECT_IRQ writer - Indicates that the device has disconnected in High-Speed mode
|
| HOST_FORCE_LS_SE0_R | Field HOST_FORCE_LS_SE0 reader - Forces the next FS packet that is transmitted to have a EOP with low-speed timing
|
| HOST_FORCE_LS_SE0_W | Field HOST_FORCE_LS_SE0 writer - Forces the next FS packet that is transmitted to have a EOP with low-speed timing
|
| R | Register CTRL_SET reader
|
| RESUMEIRQSTICKY_R | Field RESUMEIRQSTICKY reader - Resume IRQ: Set to 1 will make RESUME_IRQ bit a sticky bit until software clear it
|
| RESUMEIRQSTICKY_W | Field RESUMEIRQSTICKY writer - Resume IRQ: Set to 1 will make RESUME_IRQ bit a sticky bit until software clear it
|
| RESUME_IRQ_R | Field RESUME_IRQ reader - Resume IRQ: Indicates that the host is sending a wake-up after suspend
|
| RESUME_IRQ_W | Field RESUME_IRQ writer - Resume IRQ: Indicates that the host is sending a wake-up after suspend
|
| SFTRST_R | Field SFTRST reader - Writing a 1 to this bit will soft-reset the PWD, TX, RX, and CTRL registers
|
| SFTRST_W | Field SFTRST writer - Writing a 1 to this bit will soft-reset the PWD, TX, RX, and CTRL registers
|
| UTMI_SUSPENDM_R | Field UTMI_SUSPENDM reader - Used by the PHY to indicate a powered-down state
|
| W | Register CTRL_SET writer
|
| WAKEUP_IRQ_R | Field WAKEUP_IRQ reader - Wake-up IRQ: Indicates that there is a wak-eup event
|
| WAKEUP_IRQ_W | Field WAKEUP_IRQ writer - Wake-up IRQ: Indicates that there is a wak-eup event
|