1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108
#[doc = "Reader of register CALIB"] pub type R = crate::R<u32, super::CALIB>; #[doc = "Writer for register CALIB"] pub type W = crate::W<u32, super::CALIB>; #[doc = "Register CALIB `reset()`'s with value 0x02"] impl crate::ResetValue for super::CALIB { type Type = u32; #[inline(always)] fn reset_value() -> Self::Type { 0x02 } } #[doc = "Reader of field `CALIB`"] pub type CALIB_R = crate::R<bool, bool>; #[doc = "Write proxy for field `CALIB`"] pub struct CALIB_W<'a> { w: &'a mut W, } impl<'a> CALIB_W<'a> { #[doc = r"Sets the field bit"] #[inline(always)] pub fn set_bit(self) -> &'a mut W { self.bit(true) } #[doc = r"Clears the field bit"] #[inline(always)] pub fn clear_bit(self) -> &'a mut W { self.bit(false) } #[doc = r"Writes raw bits to the field"] #[inline(always)] pub fn bit(self, value: bool) -> &'a mut W { self.w.bits = (self.w.bits & !0x01) | ((value as u32) & 0x01); self.w } } #[doc = "Reader of field `CALREQD`"] pub type CALREQD_R = crate::R<bool, bool>; #[doc = "Write proxy for field `CALREQD`"] pub struct CALREQD_W<'a> { w: &'a mut W, } impl<'a> CALREQD_W<'a> { #[doc = r"Sets the field bit"] #[inline(always)] pub fn set_bit(self) -> &'a mut W { self.bit(true) } #[doc = r"Clears the field bit"] #[inline(always)] pub fn clear_bit(self) -> &'a mut W { self.bit(false) } #[doc = r"Writes raw bits to the field"] #[inline(always)] pub fn bit(self, value: bool) -> &'a mut W { self.w.bits = (self.w.bits & !(0x01 << 1)) | (((value as u32) & 0x01) << 1); self.w } } #[doc = "Reader of field `CALVALUE`"] pub type CALVALUE_R = crate::R<u8, u8>; #[doc = "Write proxy for field `CALVALUE`"] pub struct CALVALUE_W<'a> { w: &'a mut W, } impl<'a> CALVALUE_W<'a> { #[doc = r"Writes raw bits to the field"] #[inline(always)] pub unsafe fn bits(self, value: u8) -> &'a mut W { self.w.bits = (self.w.bits & !(0x7f << 2)) | (((value as u32) & 0x7f) << 2); self.w } } impl R { #[doc = "Bit 0 - Calibration request. Setting this bit will launch an ADC calibration cycle. This bit can only be set to a '1' by software. It is cleared automatically when the calibration cycle completes."] #[inline(always)] pub fn calib(&self) -> CALIB_R { CALIB_R::new((self.bits & 0x01) != 0) } #[doc = "Bit 1 - Calibration required. This read-only bit indicates if calibration is required when enabling the ADC. CALREQD will be '1' if no calibration has been run since the chip was powered-up and if the BYPASSCAL bit in the CTRL register is low. Software will test this bit to determine whether to initiate a calibration cycle or whether to set the ADC_INIT bit (in the STARTUP register) to launch the ADC initialization process which includes a 'dummy' conversion cycle. Note: A 'dummy' conversion cycle requires approximately 6 ADC clocks as opposed to 81 clocks required for calibration."] #[inline(always)] pub fn calreqd(&self) -> CALREQD_R { CALREQD_R::new(((self.bits >> 1) & 0x01) != 0) } #[doc = "Bits 2:8 - Calibration Value. This read-only field displays the calibration value established during last calibration cycle. This value is not typically of any use to the user."] #[inline(always)] pub fn calvalue(&self) -> CALVALUE_R { CALVALUE_R::new(((self.bits >> 2) & 0x7f) as u8) } } impl W { #[doc = "Bit 0 - Calibration request. Setting this bit will launch an ADC calibration cycle. This bit can only be set to a '1' by software. It is cleared automatically when the calibration cycle completes."] #[inline(always)] pub fn calib(&mut self) -> CALIB_W { CALIB_W { w: self } } #[doc = "Bit 1 - Calibration required. This read-only bit indicates if calibration is required when enabling the ADC. CALREQD will be '1' if no calibration has been run since the chip was powered-up and if the BYPASSCAL bit in the CTRL register is low. Software will test this bit to determine whether to initiate a calibration cycle or whether to set the ADC_INIT bit (in the STARTUP register) to launch the ADC initialization process which includes a 'dummy' conversion cycle. Note: A 'dummy' conversion cycle requires approximately 6 ADC clocks as opposed to 81 clocks required for calibration."] #[inline(always)] pub fn calreqd(&mut self) -> CALREQD_W { CALREQD_W { w: self } } #[doc = "Bits 2:8 - Calibration Value. This read-only field displays the calibration value established during last calibration cycle. This value is not typically of any use to the user."] #[inline(always)] pub fn calvalue(&mut self) -> CALVALUE_W { CALVALUE_W { w: self } } }