1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144

#[doc = "Register `RS485_CONF` reader"]
pub type R = crate::R<RS485_CONF_SPEC>;
#[doc = "Register `RS485_CONF` writer"]
pub type W = crate::W<RS485_CONF_SPEC>;
#[doc = "Field `RS485_EN` reader - Set this bit to choose the rs485 mode."]
pub type RS485_EN_R = crate::BitReader;
#[doc = "Field `RS485_EN` writer - Set this bit to choose the rs485 mode."]
pub type RS485_EN_W<'a, REG> = crate::BitWriter<'a, REG>;
#[doc = "Field `DL0_EN` reader - Set this bit to delay the stop bit by 1 bit."]
pub type DL0_EN_R = crate::BitReader;
#[doc = "Field `DL0_EN` writer - Set this bit to delay the stop bit by 1 bit."]
pub type DL0_EN_W<'a, REG> = crate::BitWriter<'a, REG>;
#[doc = "Field `DL1_EN` reader - Set this bit to delay the stop bit by 1 bit."]
pub type DL1_EN_R = crate::BitReader;
#[doc = "Field `DL1_EN` writer - Set this bit to delay the stop bit by 1 bit."]
pub type DL1_EN_W<'a, REG> = crate::BitWriter<'a, REG>;
#[doc = "Field `RS485TX_RX_EN` reader - Set this bit to enable receiver could receive data when the transmitter is transmitting data in rs485 mode."]
pub type RS485TX_RX_EN_R = crate::BitReader;
#[doc = "Field `RS485TX_RX_EN` writer - Set this bit to enable receiver could receive data when the transmitter is transmitting data in rs485 mode."]
pub type RS485TX_RX_EN_W<'a, REG> = crate::BitWriter<'a, REG>;
#[doc = "Field `RS485RXBY_TX_EN` reader - 1'h1: enable rs485 transmitter to send data when rs485 receiver line is busy."]
pub type RS485RXBY_TX_EN_R = crate::BitReader;
#[doc = "Field `RS485RXBY_TX_EN` writer - 1'h1: enable rs485 transmitter to send data when rs485 receiver line is busy."]
pub type RS485RXBY_TX_EN_W<'a, REG> = crate::BitWriter<'a, REG>;
#[doc = "Field `RS485_RX_DLY_NUM` reader - This register is used to delay the receiver's internal data signal."]
pub type RS485_RX_DLY_NUM_R = crate::BitReader;
#[doc = "Field `RS485_RX_DLY_NUM` writer - This register is used to delay the receiver's internal data signal."]
pub type RS485_RX_DLY_NUM_W<'a, REG> = crate::BitWriter<'a, REG>;
#[doc = "Field `RS485_TX_DLY_NUM` reader - This register is used to delay the transmitter's internal data signal."]
pub type RS485_TX_DLY_NUM_R = crate::FieldReader;
#[doc = "Field `RS485_TX_DLY_NUM` writer - This register is used to delay the transmitter's internal data signal."]
pub type RS485_TX_DLY_NUM_W<'a, REG> = crate::FieldWriter<'a, REG, 4>;
impl R {
    #[doc = "Bit 0 - Set this bit to choose the rs485 mode."]
    #[inline(always)]
    pub fn rs485_en(&self) -> RS485_EN_R {
        RS485_EN_R::new((self.bits & 1) != 0)
    }
    #[doc = "Bit 1 - Set this bit to delay the stop bit by 1 bit."]
    #[inline(always)]
    pub fn dl0_en(&self) -> DL0_EN_R {
        DL0_EN_R::new(((self.bits >> 1) & 1) != 0)
    }
    #[doc = "Bit 2 - Set this bit to delay the stop bit by 1 bit."]
    #[inline(always)]
    pub fn dl1_en(&self) -> DL1_EN_R {
        DL1_EN_R::new(((self.bits >> 2) & 1) != 0)
    }
    #[doc = "Bit 3 - Set this bit to enable receiver could receive data when the transmitter is transmitting data in rs485 mode."]
    #[inline(always)]
    pub fn rs485tx_rx_en(&self) -> RS485TX_RX_EN_R {
        RS485TX_RX_EN_R::new(((self.bits >> 3) & 1) != 0)
    }
    #[doc = "Bit 4 - 1'h1: enable rs485 transmitter to send data when rs485 receiver line is busy."]
    #[inline(always)]
    pub fn rs485rxby_tx_en(&self) -> RS485RXBY_TX_EN_R {
        RS485RXBY_TX_EN_R::new(((self.bits >> 4) & 1) != 0)
    }
    #[doc = "Bit 5 - This register is used to delay the receiver's internal data signal."]
    #[inline(always)]
    pub fn rs485_rx_dly_num(&self) -> RS485_RX_DLY_NUM_R {
        RS485_RX_DLY_NUM_R::new(((self.bits >> 5) & 1) != 0)
    }
    #[doc = "Bits 6:9 - This register is used to delay the transmitter's internal data signal."]
    #[inline(always)]
    pub fn rs485_tx_dly_num(&self) -> RS485_TX_DLY_NUM_R {
        RS485_TX_DLY_NUM_R::new(((self.bits >> 6) & 0x0f) as u8)
    }
}
#[cfg(feature = "impl-register-debug")]
impl core::fmt::Debug for R {
    fn fmt(&self, f: &mut core::fmt::Formatter) -> core::fmt::Result {
        f.debug_struct("RS485_CONF")
            .field("rs485_en", &self.rs485_en())
            .field("dl0_en", &self.dl0_en())
            .field("dl1_en", &self.dl1_en())
            .field("rs485tx_rx_en", &self.rs485tx_rx_en())
            .field("rs485rxby_tx_en", &self.rs485rxby_tx_en())
            .field("rs485_rx_dly_num", &self.rs485_rx_dly_num())
            .field("rs485_tx_dly_num", &self.rs485_tx_dly_num())
            .finish()
    }
}
impl W {
    #[doc = "Bit 0 - Set this bit to choose the rs485 mode."]
    #[inline(always)]
    #[must_use]
    pub fn rs485_en(&mut self) -> RS485_EN_W<RS485_CONF_SPEC> {
        RS485_EN_W::new(self, 0)
    }
    #[doc = "Bit 1 - Set this bit to delay the stop bit by 1 bit."]
    #[inline(always)]
    #[must_use]
    pub fn dl0_en(&mut self) -> DL0_EN_W<RS485_CONF_SPEC> {
        DL0_EN_W::new(self, 1)
    }
    #[doc = "Bit 2 - Set this bit to delay the stop bit by 1 bit."]
    #[inline(always)]
    #[must_use]
    pub fn dl1_en(&mut self) -> DL1_EN_W<RS485_CONF_SPEC> {
        DL1_EN_W::new(self, 2)
    }
    #[doc = "Bit 3 - Set this bit to enable receiver could receive data when the transmitter is transmitting data in rs485 mode."]
    #[inline(always)]
    #[must_use]
    pub fn rs485tx_rx_en(&mut self) -> RS485TX_RX_EN_W<RS485_CONF_SPEC> {
        RS485TX_RX_EN_W::new(self, 3)
    }
    #[doc = "Bit 4 - 1'h1: enable rs485 transmitter to send data when rs485 receiver line is busy."]
    #[inline(always)]
    #[must_use]
    pub fn rs485rxby_tx_en(&mut self) -> RS485RXBY_TX_EN_W<RS485_CONF_SPEC> {
        RS485RXBY_TX_EN_W::new(self, 4)
    }
    #[doc = "Bit 5 - This register is used to delay the receiver's internal data signal."]
    #[inline(always)]
    #[must_use]
    pub fn rs485_rx_dly_num(&mut self) -> RS485_RX_DLY_NUM_W<RS485_CONF_SPEC> {
        RS485_RX_DLY_NUM_W::new(self, 5)
    }
    #[doc = "Bits 6:9 - This register is used to delay the transmitter's internal data signal."]
    #[inline(always)]
    #[must_use]
    pub fn rs485_tx_dly_num(&mut self) -> RS485_TX_DLY_NUM_W<RS485_CONF_SPEC> {
        RS485_TX_DLY_NUM_W::new(self, 6)
    }
}
#[doc = "RS485 mode configuration\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`rs485_conf::R`](R).  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`rs485_conf::W`](W). You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api)."]
pub struct RS485_CONF_SPEC;
impl crate::RegisterSpec for RS485_CONF_SPEC {
    type Ux = u32;
}
#[doc = "`read()` method returns [`rs485_conf::R`](R) reader structure"]
impl crate::Readable for RS485_CONF_SPEC {}
#[doc = "`write(|w| ..)` method takes [`rs485_conf::W`](W) writer structure"]
impl crate::Writable for RS485_CONF_SPEC {
    type Safety = crate::Unsafe;
    const ZERO_TO_MODIFY_FIELDS_BITMAP: u32 = 0;
    const ONE_TO_MODIFY_FIELDS_BITMAP: u32 = 0;
}
#[doc = "`reset()` method sets RS485_CONF to value 0"]
impl crate::Resettable for RS485_CONF_SPEC {
    const RESET_VALUE: u32 = 0;
}