Struct aws_sdk_directconnect::model::connection::Builder

#[non_exhaustive]
pub struct Builder { /* private fields */ }

A builder for Connection

Implementations

impl Builder

pub fn owner_account(self, input: impl Into<String>) -> Self

The ID of the Amazon Web Services account that owns the connection.

pub fn set_owner_account(self, input: Option<String>) -> Self

The ID of the Amazon Web Services account that owns the connection.

pub fn connection_id(self, input: impl Into<String>) -> Self

The ID of the connection.

pub fn set_connection_id(self, input: Option<String>) -> Self

The ID of the connection.

pub fn connection_name(self, input: impl Into<String>) -> Self

The name of the connection.

pub fn set_connection_name(self, input: Option<String>) -> Self

The name of the connection.

pub fn connection_state(self, input: ConnectionState) -> Self

The state of the connection. The following are the possible values:

• ordering: The initial state of a hosted connection provisioned on an interconnect. The connection stays in the ordering state until the owner of the hosted connection confirms or declines the connection order.

• requested: The initial state of a standard connection. The connection stays in the requested state until the Letter of Authorization (LOA) is sent to the customer.

• pending: The connection has been approved and is being initialized.

• available: The network link is up and the connection is ready for use.

• down: The network link is down.

• deleting: The connection is being deleted.

• deleted: The connection has been deleted.

• rejected: A hosted connection in the ordering state enters the rejected state if it is deleted by the customer.

• unknown: The state of the connection is not available.

pub fn set_connection_state(self, input: Option<ConnectionState>) -> Self

The state of the connection. The following are the possible values:

• ordering: The initial state of a hosted connection provisioned on an interconnect. The connection stays in the ordering state until the owner of the hosted connection confirms or declines the connection order.

• requested: The initial state of a standard connection. The connection stays in the requested state until the Letter of Authorization (LOA) is sent to the customer.

• pending: The connection has been approved and is being initialized.

• available: The network link is up and the connection is ready for use.

• down: The network link is down.

• deleting: The connection is being deleted.

• deleted: The connection has been deleted.

• rejected: A hosted connection in the ordering state enters the rejected state if it is deleted by the customer.

• unknown: The state of the connection is not available.

pub fn region(self, input: impl Into<String>) -> Self

The Amazon Web Services Region where the connection is located.

pub fn set_region(self, input: Option<String>) -> Self

The Amazon Web Services Region where the connection is located.

pub fn location(self, input: impl Into<String>) -> Self

The location of the connection.

pub fn set_location(self, input: Option<String>) -> Self

The location of the connection.

pub fn bandwidth(self, input: impl Into<String>) -> Self

The bandwidth of the connection.

pub fn set_bandwidth(self, input: Option<String>) -> Self

The bandwidth of the connection.

pub fn vlan(self, input: i32) -> Self

The ID of the VLAN.

pub fn set_vlan(self, input: Option<i32>) -> Self

The ID of the VLAN.

pub fn partner_name(self, input: impl Into<String>) -> Self

The name of the Direct Connect service provider associated with the connection.

pub fn set_partner_name(self, input: Option<String>) -> Self

The name of the Direct Connect service provider associated with the connection.

pub fn loa_issue_time(self, input: DateTime) -> Self

The time of the most recent call to DescribeLoa for this connection.

pub fn set_loa_issue_time(self, input: Option<DateTime>) -> Self

The time of the most recent call to DescribeLoa for this connection.

pub fn lag_id(self, input: impl Into<String>) -> Self

The ID of the LAG.

pub fn set_lag_id(self, input: Option<String>) -> Self

The ID of the LAG.

pub fn aws_device(self, input: impl Into<String>) -> Self

The Direct Connect endpoint on which the physical connection terminates.

pub fn set_aws_device(self, input: Option<String>) -> Self

The Direct Connect endpoint on which the physical connection terminates.

pub fn jumbo_frame_capable(self, input: bool) -> Self

Indicates whether jumbo frames (9001 MTU) are supported.

pub fn set_jumbo_frame_capable(self, input: Option<bool>) -> Self

Indicates whether jumbo frames (9001 MTU) are supported.

pub fn aws_device_v2(self, input: impl Into<String>) -> Self

The Direct Connect endpoint that terminates the physical connection.

pub fn set_aws_device_v2(self, input: Option<String>) -> Self

The Direct Connect endpoint that terminates the physical connection.

pub fn aws_logical_device_id(self, input: impl Into<String>) -> Self

The Direct Connect endpoint that terminates the logical connection. This device might be different than the device that terminates the physical connection.

pub fn set_aws_logical_device_id(self, input: Option<String>) -> Self

The Direct Connect endpoint that terminates the logical connection. This device might be different than the device that terminates the physical connection.

pub fn has_logical_redundancy(self, input: HasLogicalRedundancy) -> Self

Indicates whether the connection supports a secondary BGP peer in the same address family (IPv4/IPv6).

pub fn set_has_logical_redundancy(
    self,
    input: Option<HasLogicalRedundancy>
) -> Self

Indicates whether the connection supports a secondary BGP peer in the same address family (IPv4/IPv6).

pub fn tags(self, input: Tag) -> Self

Appends an item to tags.

To override the contents of this collection use set_tags.

The tags associated with the connection.

pub fn set_tags(self, input: Option<Vec<Tag>>) -> Self

The tags associated with the connection.

pub fn provider_name(self, input: impl Into<String>) -> Self

The name of the service provider associated with the connection.

pub fn set_provider_name(self, input: Option<String>) -> Self

The name of the service provider associated with the connection.

pub fn mac_sec_capable(self, input: bool) -> Self

Indicates whether the connection supports MAC Security (MACsec).

pub fn set_mac_sec_capable(self, input: Option<bool>) -> Self

Indicates whether the connection supports MAC Security (MACsec).

pub fn port_encryption_status(self, input: impl Into<String>) -> Self

The MAC Security (MACsec) port link status of the connection.

The valid values are Encryption Up, which means that there is an active Connection Key Name, or Encryption Down.

pub fn set_port_encryption_status(self, input: Option<String>) -> Self

The MAC Security (MACsec) port link status of the connection.

The valid values are Encryption Up, which means that there is an active Connection Key Name, or Encryption Down.

pub fn encryption_mode(self, input: impl Into<String>) -> Self

The MAC Security (MACsec) connection encryption mode.

The valid values are no_encrypt, should_encrypt, and must_encrypt.

pub fn set_encryption_mode(self, input: Option<String>) -> Self

The MAC Security (MACsec) connection encryption mode.

The valid values are no_encrypt, should_encrypt, and must_encrypt.

pub fn mac_sec_keys(self, input: MacSecKey) -> Self

Appends an item to mac_sec_keys.

To override the contents of this collection use set_mac_sec_keys.

The MAC Security (MACsec) security keys associated with the connection.

pub fn set_mac_sec_keys(self, input: Option<Vec<MacSecKey>>) -> Self

The MAC Security (MACsec) security keys associated with the connection.

pub fn build(self) -> Connection

Consumes the builder and constructs a Connection

Trait Implementations

impl Clone for Builder

fn clone(&self) -> Builder

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for Builder

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Default for Builder

fn default() -> Builder

Returns the “default value” for a type.

impl PartialEq<Builder> for Builder

fn eq(&self, other: &Builder) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Builder) -> bool

This method tests for !=.

impl StructuralPartialEq for Builder