Struct aws_sdk_directconnect::model::bgp_peer::Builder

#[non_exhaustive]
pub struct Builder { /* private fields */ }

A builder for BgpPeer

Implementations

impl Builder

pub fn bgp_peer_id(self, input: impl Into<String>) -> Self

The ID of the BGP peer.

pub fn set_bgp_peer_id(self, input: Option<String>) -> Self

The ID of the BGP peer.

pub fn asn(self, input: i32) -> Self

The autonomous system (AS) number for Border Gateway Protocol (BGP) configuration.

pub fn set_asn(self, input: Option<i32>) -> Self

The autonomous system (AS) number for Border Gateway Protocol (BGP) configuration.

pub fn auth_key(self, input: impl Into<String>) -> Self

The authentication key for BGP configuration. This string has a minimum length of 6 characters and and a maximun lenth of 80 characters.

pub fn set_auth_key(self, input: Option<String>) -> Self

The authentication key for BGP configuration. This string has a minimum length of 6 characters and and a maximun lenth of 80 characters.

pub fn address_family(self, input: AddressFamily) -> Self

The address family for the BGP peer.

pub fn set_address_family(self, input: Option<AddressFamily>) -> Self

The address family for the BGP peer.

pub fn amazon_address(self, input: impl Into<String>) -> Self

The IP address assigned to the Amazon interface.

pub fn set_amazon_address(self, input: Option<String>) -> Self

The IP address assigned to the Amazon interface.

pub fn customer_address(self, input: impl Into<String>) -> Self

The IP address assigned to the customer interface.

pub fn set_customer_address(self, input: Option<String>) -> Self

The IP address assigned to the customer interface.

pub fn bgp_peer_state(self, input: BgpPeerState) -> Self

The state of the BGP peer. The following are the possible values:

• verifying: The BGP peering addresses or ASN require validation before the BGP peer can be created. This state applies only to public virtual interfaces.

• pending: The BGP peer is created, and remains in this state until it is ready to be established.

• available: The BGP peer is ready to be established.

• deleting: The BGP peer is being deleted.

• deleted: The BGP peer is deleted and cannot be established.

pub fn set_bgp_peer_state(self, input: Option<BgpPeerState>) -> Self

The state of the BGP peer. The following are the possible values:

• verifying: The BGP peering addresses or ASN require validation before the BGP peer can be created. This state applies only to public virtual interfaces.

• pending: The BGP peer is created, and remains in this state until it is ready to be established.

• available: The BGP peer is ready to be established.

• deleting: The BGP peer is being deleted.

• deleted: The BGP peer is deleted and cannot be established.

pub fn bgp_status(self, input: BgpStatus) -> Self

The status of the BGP peer. The following are the possible values:

• up: The BGP peer is established. This state does not indicate the state of the routing function. Ensure that you are receiving routes over the BGP session.

• down: The BGP peer is down.

• unknown: The BGP peer status is not available.

pub fn set_bgp_status(self, input: Option<BgpStatus>) -> Self

The status of the BGP peer. The following are the possible values:

• up: The BGP peer is established. This state does not indicate the state of the routing function. Ensure that you are receiving routes over the BGP session.

• down: The BGP peer is down.

• unknown: The BGP peer status is not available.

pub fn aws_device_v2(self, input: impl Into<String>) -> Self

The Direct Connect endpoint that terminates the BGP peer.

pub fn set_aws_device_v2(self, input: Option<String>) -> Self

The Direct Connect endpoint that terminates the BGP peer.

pub fn aws_logical_device_id(self, input: impl Into<String>) -> Self

The Direct Connect endpoint that terminates the logical connection. This device might be different than the device that terminates the physical connection.

pub fn set_aws_logical_device_id(self, input: Option<String>) -> Self

The Direct Connect endpoint that terminates the logical connection. This device might be different than the device that terminates the physical connection.

pub fn build(self) -> BgpPeer

Consumes the builder and constructs a BgpPeer

Trait Implementations

impl Clone for Builder

fn clone(&self) -> Builder

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for Builder

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Default for Builder

fn default() -> Builder

Returns the “default value” for a type.

impl PartialEq<Builder> for Builder

fn eq(&self, other: &Builder) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Builder) -> bool

This method tests for !=.

impl StructuralPartialEq for Builder